fbpx
Handlekurv

Sign up to our newsletter and get 15% discount on your first order. Get discount code

Feilsøking

Nedenfor er noen av de vanligste lyssignalene som indikerer forskjellig status på SMART BRAKE. Hvis du trenger ytterligere hjelp, ikke nøl med å kontakte oss eller bruke vår technical support

Søvn-modus

After 60 minutes of inactivity, both the brake unit (s) and the control (s) go into power save mode (standby). In this mode the system stops sending out signals to save battery.

  1. To “wake” the brake unit(s) push the activation button on (both) unit(s) once.
  2. To “wake” the remote(s) trigger the brake after the unit(s) has been activated.

NOTE: If not all controls are awakened after sleep-mode will fail-safe be activated.

Break Lever

TroublePossible CauseRemedy
Everything is functional, but there is no lightning signalsPossible defect lightning sourceSend to service
There are no functions or lightning signalsDrained batteryCharge for 2,5 hours
I have charge for 2,5 hours but there is no function or light signalsDirective charger or batteriTry another charger if it does not work – Send to service
A red flash every ten secondBattery level under 25%Charge whenever possible.
A red flash every secondFail-Safe activated = Battery level under 15%Charge now
Grenn/blue flash while squeezing the leverLost contact with the Brake UnitSet the Brake Unit in synchronization modus and connect the remote
Blue constant light signalWhile charging, squeeze the lever for five seconds. This activates bootloader mode.Disconnect the charger from the brake lever and wait one minute

Bremseenhet

TroublePossible CauseRemedy
Everything is functional, but there is no lightning signalsPossible defect lightning sourceSend to service
There are no functions or lightning signalsDrained batteryCharge for 3,5 hours
I have charge for 3,5 hours but there is no function or light signalsDirective charger or batteriTry another charger if it does not work – Send to service
I have two Brake Units and only one of them worksLost connection between one Brake UnitOne Brake Unit is dischargedSet the working Brake Unit in synchronization modus, then connect the other Brake Unit.Charge the Brake Unit.
When starting the Brake Units, they go straight into Fail-Safe mode.The remotes are in sleep mode and need to be awaked. Check the light signals from the remotes.Activate alle remotes by doing a brake sequence. Charge or re-connect the remote.
Activation button at the Brake Unit does not work The button might be stuck. When stuck there is no “click” sound when pushing it. Try to push the button from different directions to see if it loosens
Brake Light and USB Light flashes red every ten secondsUnder 25% battery capacityCharge whenever possible.
Brake Light flashes every second and the USB light does not flashFail-Safe activated = Battery level under 15%Turn off the Brake Unit by holding the activation button for 5 seconds. This will open the brakes, but the remotes will not work as the system it turned off. Charge as soon as possible.
Brake Light and USB Light flashes yellow every secondFail-Safe activated because of the Brake Remote has a battery level under 15%Turn off the Brake Unit by holding the activation button for 5 secounds. This will open the brakes, but the remotes will not work as the system it turned off. Charge as soon as possible.
Brake Light and USB Light flashes blue every secondFail-Safe is activated because there is a signal failure between on of the remotes and the Brake Unit.Signal failure signaled by: Bremsehendel flashes Blue/Green when squeezing the lever.Tommelbrems flashes blue when l squeezing the lever.Håndkontroll flashes red when squeezing the button.

Ledsagerstyring

Signalfeil aktiverer sikkerhetsbremsen (fail-safe). Når en fjernkontroll kommer utenfor rekkevidden til bremseenheten (20-30m), aktiveres sikkerhetsbremsen. Når signalet er gjenopprettet, avsluttes bremsesyklusen, og hjulene vil ikke lenger være låst. Det tar to sekunder fra kontrollen mister signalet til fail-safe er aktivert. Sikkerhetsbremsen sørger for at ledsageren alltid har kontakt med bremsene i alle situasjoner

Lading

Use the RollerSafe charger for both the brake Unit and the brake Lever. Brake trigger and Hand control uses a CR2032 battery. Fully charged is signified by a green light after 3,5 hours.

Velg valuta
EUREuro